Deformability analysis of the AISI 304 DDQ stainless steel under deep drawing multiaxial condition. Evaluation of the initial strain influence

Authors

  • J. Coello Instituto de Desarrollo Regional; Universidad de Castilla-La Mancha
  • V. Miguel Instituto de Desarrollo Regional; Universidad de Castilla-La Mancha
  • A. Calatayud Instituto de Desarrollo Regional; Universidad de Castilla-La Mancha
  • A. Martínez Instituto de Desarrollo Regional; Universidad de Castilla-La Mancha
  • C. Ferrer Departamento de Ingeniería Mecánica y de Materiales; Universidad Politécnica de Valencia

DOI:

https://doi.org/10.3989/revmetalm.0967

Keywords:

Formability, Anisotropy, Initial strain state, 304 DDQ

Abstract


The deep drawing formability of a material is established as a function of standard indexes, as strength coefficient and anisotropy coefficient. But these indexes are determined in different conditions to those that take place in the forming process. The simulative assays do not separate the actions due to the different variables that work in the process, as for example, the rolling direction. In the present work a test that uses a wedge shape die is considered in order to obtain the strength and anisotropy coefficients as a function of rolling direction. This way, the assays are carried out under a tensile-biaxial compression stress state similar to that one taking place in the flange zone in deep drawing. The experimented material is a deep drawing quality stainless steel AISI 304. The influence of initial strengthened states, rolling and uniaxial tensile on the steel behaviour are also studied. The results permits the authors establish the validity of the assay from the point of view of the strains produced in the sheet. The initial strain has a higher effect on the material than that one obtained from the tensile-biaxial of the state than the tensile-biaxial compression causes. The anisotropy coefficient changes with the strain for the sheet rolling direction.

Downloads

Download data is not yet available.

References

[1] D. C. Chiang y S. Kobayashi, J. Eng. Ind. (1966) 443-448.

[2] D.M.Woo, J.Mech. Eng. Sci. 2 (1964) 116-131. doi:10.1243/JMES_JOUR_1964_006_021_02

[3] E. Gao, W. Li, H. Kou, H. Changa, J. Li y L. Zhou, Trans. Nonferrous Met. Soc. China 19 (2009) 433-437. doi:10.1016/S1003-6326(08)60291-5

[4] C. García, D. Celentano, F. Flores, J.P. Ponthot y O. Oliva. J.Mater. Proc. Technol. 172 (2006) 461-471. doi:10.1016/j.jmatprotec.2005.11.016

[5] S. Holmberg, B. Enquist y P. Thilderkvist, J. Mater. Process. Tech. 147 (2004) 72-83. doi:10.1016/j.jmatprotec.2003.07.004

[6] J.L.Geoffroy, J.Goncalves y X. Lemoine, IDDRG 2007 Conf., Györ, Hungría, pp.177-180.

[7] L. Kessler,H. Richter, K. Roll yA. Faust, IDDRG 2007 Conf., Györ, Hungría, pp. 101-108.

[8] V. Miguel, J. Benet, J. Coello, A. Calatayud y A.Martínez,Mater. Proc. Design.Model., Simul. Appl. (2007) pp. 823-828.

[9] ASMHandbook. Vol. 14B (2005) pp. 673-696.

[10] S. Rajagopal, J. Eng. Ind. 103 (1981) 197-202. doi:10.1115/1.3184475

[11] L. Gunnarson, N. Asnafi y E. Schedin, J.Mater. Process. Tech. 73 (1998) 89-96. doi:10.1016/S0924-0136(97)00217-3

[12] T. Yagami, K.Manabe y Y. Yamauchi, J.Mater. Process. Tech. (2007) 187-191.

[13] V.Miguel, C. Ferrer y A. Calatayud, Rev.Metal. Madrid 43 (2007) 146-156.

[14] V.Miguel, J. Coello, A. Calatayud, M.C. Manjabacas, A. Martínez y C. Ferrer. J. Mater. Process. Tech. 209 (2009) 1.588-1.596.

[15] J.Coello,V.Miguel,A.Calatayud,C. Ferrer yA. Martínez, Rev.Metal.Madrid 44 (2008) 503-512.

[16] UNE EN ISO 36404:1988 EX.

[17] J. Coello, V. Miguel, C. Ferrer, A. Calatayud y A.Martínez, Rev.Metal.Madrid 45 (2009) 351- 364.

[18] G. W. Rowe, Conformado de los metales, Ed. Hurmo, Bilbao, 1972, pp. 86-95.

[19] N. Kawai, N. Hayashi y S. Matsui, Trans. ASME 110 (1988) 376-383. doi:10.1115/1.3187897

Downloads

Published

2010-10-30

How to Cite

Coello, J., Miguel, V., Calatayud, A., Martínez, A., & Ferrer, C. (2010). Deformability analysis of the AISI 304 DDQ stainless steel under deep drawing multiaxial condition. Evaluation of the initial strain influence. Revista De Metalurgia, 46(5), 435–445. https://doi.org/10.3989/revmetalm.0967

Issue

Section

Articles

Most read articles by the same author(s)

1 2 > >>