Aumento de calidad en uniones soldadas de estructuras de paredes delgadas mediante modelo de simulación

Myroslav Panchuk; Oleh Matviienkiv; Lubomyr Shlapak; Marek Szkodo; Wojciech Kiełczynski; Andrii Panchuk

doi:10.3989/revmetalm.158

Quality increase for single-welded joints of thin-walled structures by means of simulation modelling

Authors

Myroslav Panchuk Ivano-Frankivsk National Technical University of Oil and Gas (IFNTUOG) https://orcid.org/0000-0002-4898-2707
Oleh Matviienkiv Ivano-Frankivsk National Technical University of Oil and Gas (IFNTUOG) https://orcid.org/0000-0003-1717-5416
Lubomyr Shlapak Ivano-Frankivsk National Technical University of Oil and Gas (IFNTUOG) https://orcid.org/0000-0002-4522-7300
Marek Szkodo Politechnika Gdańska https://orcid.org/0000-0002-4210-0718
Wojciech Kiełczynski Politechnika Gdańska https://orcid.org/0000-0001-5727-9530
Andrii Panchuk Politechnika Gdańska https://orcid.org/0000-0003-1784-7374

DOI:

https://doi.org/10.3989/revmetalm.158

Keywords:

Weld modeling, Welding thin-walled structures

Abstract

The Simulation calculation module and the SolidWorks software package have helped to define the optimal shape and dimensions of single-welded joints which may serve the basis for calculating the process parameters of welding. Having compared the models with different weld cross-sections the authors have defined that the weld height and width do not significantly affect the stress concentration, and the stress concentration and value mainly depend on the shape of the root bead and the gap size between the welded parts.

Downloads

Download data is not yet available.

References

GouMing, H., ShaoHui, Y., XinHua, C., JunYue, L. (2003). Acquisition and pattern recognition of spectrum information of welding metal transfer. Mater. Design 24 (8), 699-703. https://doi.org/10.1016/S0261-3069(03)00092-X

Guoqing, G., Yuping, Y., Hui, C. (2014). An ICME Approach for Optimizing Thin-Welded Structure Design. Engineering 6 (13), 936-947. https://doi.org/10.4236/eng.2014.613085

Islam, M., Buijk, A., Rais-Rohani, M., Motoyama, K. (2014). Simulation-based numerical optimization of arc welding process for reduced distortion in welded structures. Finite Elem. Anal. Des. 84, 54-64. https://doi.org/10.1016/j.finel.2014.02.003

Mochizuki, M., Mikami, Y., Toyoda, M., Yamasaki, H. (2007). Elastic predicting of weld distortion of large structures using numerical simulation results by thermal-elastic-plastic analysis of small components. Weld. World 51 (11-12), 60-64. https://doi.org/10.1007/BF03266609

Murakawa, H., Sano, ?., Wang, J. (2012). Influence of Root Gap and Tack Weld on Transverse Shrinkage during Welding. Trans. JWRI 41 (1), 65-70.

Romeo-Hdz, J., Saha, B.N., Toledo, G. (2016). Welding Sequence Optimization through a Modified Lowest Cost Search Algoritm. Comput. Sci. Eng. 6 (2), 25-32.

Soul, F., Hamdy, N. (2012). Numerical Simulation of Residual Stress and Strain Behavior After Temperature Modification. INTECH Open Access Publisher, pp. 217-246. https://doi.org/10.5772/47745

Zasyad'ko, I.Z., Korinecy, I.P. (2010). Welding of thin-sheet construction. 5, 81-87. Research Bulletin of the National Technical University of Ukraine "Kyiv Politechnic Institute". http://nbuv.gov.ua/UJRN/NVKPI_2010_5_13.

Downloads

Published

2019-12-30

How to Cite

Panchuk, M., Matviienkiv, O., Shlapak, L., Szkodo, M., Kiełczynski, W., & Panchuk, A. (2019). Quality increase for single-welded joints of thin-walled structures by means of simulation modelling. Revista De Metalurgia, 55(4), e158. https://doi.org/10.3989/revmetalm.158

Download Citation

Issue

Vol. 55 No. 4 (2019)

Section

Articles

License

This work is licensed under a Creative Commons Attribution 4.0 International License.

© CSIC. Manuscripts published in both the printed and online versions of this Journal are the property of Consejo Superior de Investigaciones Científicas, and quoting this source is a requirement for any partial or full reproduction.

All contents of this electronic edition, except where otherwise noted, are distributed under a “Creative Commons Attribution 4.0 International” (CC BY 4.0) License. You may read here the basic information and the legal text of the license. The indication of the CC BY 4.0 License must be expressly stated in this way when necessary.

Self-archiving in repositories, personal webpages or similar, of any version other than the published by the Editor, is not allowed.