Characterization by EBSD technique of AISI 304 DDQ stainless steel sheet deformed under typical deep drawing multiaxial stress system
DOI:
https://doi.org/10.3989/revmetalm.0842Keywords:
Stainless steel, Deep drawing, EBSD, AnisotropyAbstract
The main aim of this work is to evaluate AISI 304 DDQ stainless steel behaviour under deep drawing deformation condition, that is, pure shear deformation in which material suffers a typical deformation under tension-biaxial compression stresses system. The microestructural evolution has been investigated by optical microscopy and by EBSD technique. The success of the EBSD analysis has been established for the deformation conditions experimented here. It has been determined the rolling direction and the equivalent strain influence on the crystallographic orientation maps, misorientation diagrams and poles figures. The results let the authors say the low angle misorientations corresponding to 0, 45 and 90° rolling directions have an inverse correlation with the material anisotropy. Initial prestraining has been considered also and the analysis of this aspects lead to establish that the increment of the intragranular misorientations with the strain depends on the initial state of the steel; this increment is observed to be minor for samples with initial prestraining. High angle misorientation analysis (>15°) indicates that the grain boundaries character distributions depends on the deformation.
Downloads
References
[1] G. Berming, J. Tobisch y K. Helming, Proc. Of the 10th Int. Conf. Textures of Materials,1994, Vol. 157-162, pp. 1.953-1.961.
[2] V. Randle, Introduction to Texture Analysis: Macrotexture, Microtexture and Orientation Mapping, Ed. OPA, Florida, 2000, cap 6, pp. 127-142.
[3] A.J. Schwartz et al., Electron Backscattered Diffraction in Materials Science, Ed. Plenum Publishers, New York, 2000, cap. 19, pp. 231-244.
[4] M. El Wahabi, L. Gavard, F. Montheillet, J.M. Cabrera y J.M. Prado, Acta Mater. 53 (2005) 4605-4612. doi:10.1016/j.actamat.2005.06.020
[5] D. Jorge-Badiola, A. Iza-Mendia e I. Gutiérrez, Mater. Sci. Eng. A 394 (2005) 445-454. doi:10.1016/j.msea.2004.11.049
[6] M. El Wahabi, L. Gavard, J.M. Cabrera, J.M. Prado y F. Montheillet, Mater. Sci. Eng. A 393 (2005) 83-90. doi:10.1016/j.msea.2004.09.064
[7] M. El Wahabi, J. M. Cabrera y J. M. Prado, Mater. Sci. Eng. A 343 (2003) 116-125. doi:10.1016/S0921-5093(02)00357-X
[8] Q. Xue, J.F. Bingert, B.L. Henrie y G.T. Gray, Mater. Sci. Eng. A 473 (2008) 279-289. doi:10.1016/j.msea.2007.04.048
[9] Q. Xue, X.Z. Liao, Y.T. Zhu y G.T. Gray, Mater. Sci. Eng. A 410-411 (2005) 252-256. doi:10.1016/j.msea.2005.08.022
[10] Q. Xue, M.A. Meyers y V.F. Nesterenko, Mater. Sci. Eng. A 384 (2004) 35-46. doi:10.1016/j.msea.2004.05.069
[11] M. A. Meyers, Y.B. Xu, Q. Xue, M.T. Pérez- Prado y T.R. McNelley, Acta Mater. 51 (2003) 1.307-1.325.
[12] M. Humbert, B. Petit, B. Bolle y N. Gey, Mater. Sci. Eng. A 454-455 (2007) 508-517. doi:10.1016/j.msea.2006.11.112
[13] B. Petit, N. Gey, M. Cherkaoui, B. Bolle y M. Humbert, Int J Plasticity 23 (2007) 323-341. doi:10.1016/j.ijplas.2006.07.002
[14] V. Miguel, Tesis Doctoral, Universidad Politécnica de Valencia, 2005.
[15] V. Miguel, J. Coello, A. Calatayud, C. Ferrer y A. Martínez. Proc. Int. Deep Drawing Research Group, 2007, pp. 221-228.
[16] UNE EN ISO 10088-2: Parte 2.
[17] V. Miguel, C. Ferrer y A. Calatayud. Rev. Metal. Madrid 43 (2007) 142-152. doi:10.3989/revmetalm.2007.v43.i2.61
[18] V. Miguel, C. Ferrer, A. Calatayud, A. Martínez y J. Coello, Proc. Int.Deep Drawing Research Group, IDDRG´06, 2006, pp. 223-229.
[19] V. Miguel, J. Benet, J. Coello, A. Calatayud y A. Martínez, Materials Processing and Design. Modeling, Simulation and Applications, 2007, pp. 823-828.
[20] M. Kamaya, A.J. Wilkinson y J.M. Titchmarsh, Acta Mater. 54 (2006) 539-548. doi:10.1016/j.actamat.2005.08.046
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2009 Consejo Superior de Investigaciones Científicas (CSIC)

This work is licensed under a Creative Commons Attribution 4.0 International License.
© CSIC. Manuscripts published in both the printed and online versions of this Journal are the property of Consejo Superior de Investigaciones Científicas, and quoting this source is a requirement for any partial or full reproduction.All contents of this electronic edition, except where otherwise noted, are distributed under a “Creative Commons Attribution 4.0 International” (CC BY 4.0) License. You may read here the basic information and the legal text of the license. The indication of the CC BY 4.0 License must be expressly stated in this way when necessary.
Self-archiving in repositories, personal webpages or similar, of any version other than the published by the Editor, is not allowed.