Effect of boron treatment on the microstructure and toughness of Ti-containing steel weld metals
DOI:
https://doi.org/10.3989/revmetalm.223Keywords:
Weld metal, Acicular ferrite, Boron content, Hardenability, ToughnessAbstract
Ti-containing steel weld metals with boron addition contents of 0-85 ppm were prepared, and their microstructural characteristics as well as the impact toughness were investigated. The results show that in these microstructures, compared to the weld metal without boron, the addition of 22-39 ppm boron results in a remarkable increase in the amount of acicular ferrite at the expense of grain boundary ferrite, idiomorphic ferrite and side-plate ferrite. However, with a further increase in the boron content up to 61-85 ppm, the bainitic ferrite is formed, accompanied with a drop in the amount of acicular ferrite. In the acicular ferrite, the size of martensite-austenite (M/A) islands is much smaller, and the amount is much lower than those found in the bainitic ferrite. In the case of the weld metals primarily composed of acicular ferrite, during the fracture of the impact specimens, the crack propagation path is more bent in comparison with the weld metals with large amounts of grain boundary ferrite, idiomorphic ferrite, side-plate ferrite or bainitic ferrite, which that the presence of acicular ferrite improves the toughness of the weld metals. The coarse martensite-austenite islands readily induce micro-cracks at the interface between martensite-austenite islands and ferrite matrix, deteriorating the toughness. The weld metals with B contents of 22-39 ppm exhibit outstanding impact toughness because of high amount of acicular ferrite, accompanied with fine martensite-austenite islands.
Downloads
References
Abson, D.J. (2018). Acicular ferrite and bainite in C-Mn and low alloy steel arc weld metals. Sci. Technol. Weld. Join. 23 (8), 635-648. https://doi.org/10.1080/13621718.2018.1461992
Chaveriat, P.F., Kim, G.S., Shah, S., Indacochea, J.E. (1987). Low carbon steel weld metal microstructures: The role of oxygen and manganese. J. Mater. Eng. 9 (3), 253-267. https://doi.org/10.1007/BF02834145
Chen, J.H., Kikuta, Y., Araki, T., Yoneda, M., Matsuda, Y. (1984). Micro-fracture behaviour induced by M-A constituent (Island Martensite) in simulated welding heat affected zone of HT80 high strength low alloyed steel. Acta Metall. 32 (10), 1779-1788. https://doi.org/10.1016/0001-6160(84)90234-7
Cui, J., Zhu, W., Chen, Z., Chen, L. (2020). Effect of simulated cooling time on microstructure and toughness of CGHAZ in novel high-strength low-carbon construction steel. Sci. Technol. Weld. Join. 25 (2), 169-177. https://doi.org/10.1080/13621718.2019.1661116
Davis, C.L., King, J.E. (1994). Cleavage initiation in the intercritically reheated coarse-grained heat-affected zone: Part I. Fractographic evidence. Metall. Mater. Trans. A 25 (3), 563-573. https://doi.org/10.1007/BF02651598
Dowling, J.M., Corbett, J.M., Kerr, H.W. (1986). Inclusion phases and the nucleation of acicular ferrite in submerged arc welds in high strength low alloy steels. Metall. Mater. Trans. A 17 (9), 1611-1623. https://doi.org/10.1007/BF02650098
Farrar, R.A., Harrison, P.L. (1987). Acicular ferrite in carbon-manganese weld metals: An overview. J. Mater. Sci. 22 (11), 3812-3820. https://doi.org/10.1007/BF01133327
Ferrante, M., Farrar, R.A. (1982). The role of oxygen rich inclusions in determining the microstructure of weld metal deposits. J. Mater. Sci. 17 (11), 3293-3298. https://doi.org/10.1007/BF01203498
Fujiyama, N., Shigesato, G. (2021). Effects of Mn and Al on acicular ferrite formation in SAW weld metal. ISIJ Int. 61 (5), 1614-1622. https://doi.org/10.2355/isijinternational.ISIJINT-2020-407
Han, F., Hwang, B., Suh, D.W., Wang, Z.C., Lee, D.L., Kim, S.J. (2008). Effect of molybdenum and chromium on hardenability of low-carbon boron-added steels. Met. Mater. Int. 14 (6), 667-672. https://doi.org/10.3365/met.mat.2008.12.667
He, X.L., Chu, Y.Y., Jonas, J.J. (1989). Grain boundary segregation of boron during continuous cooling. Acta Metall. 37 (1), 147-161. https://doi.org/10.1016/0001-6160(89)90274-5
Jorge, J.C.F., Souza, L.F.G., Mendes, M.C., Bott, I.S., Araujo, L.S., Dos Santos, V.R., Rebello, J.M.A., Evans, G.M. (2021). Microstructure characterization and its relationship with impact toughness of C-Mn and high strength low alloy steel weld metals - A review. J. Mater. Res. Technol. 10, 471-501. https://doi.org/10.1016/j.jmrt.2020.12.006
Lan, L., Qiu, C., Zhao, D., Gao, X., Du, L. (2012). Analysis of martensite-austenite constituent and its effect on toughness in submerged arc welded joint of low carbon bainitic steel. J. Mater. Sci. 47 (11), 4732-4742. https://doi.org/10.1007/s10853-012-6346-x
Lan, L., Qiu, C., Song, H., Zhao, D. (2014). Correlation of martensite-austenite constituent and cleavage crack initiation in welding heat affected zone of low carbon bainitic steel. Mater. Lett. 125, 86-88. https://doi.org/10.1016/j.matlet.2014.03.123
Lee, J.L., Pan, Y.T. (1995). The formation of intragranular acicular ferrite in simulated heat-affected zone. ISIJ Int. 35 (8), 1027-1033. https://doi.org/10.2355/isijinternational.35.1027
Li, C., Wang, Y., Chen, Y. (2011). Influence of peak temperature during in-service welding of API X70 pipeline steels on microstructure and fracture energy of the reheated coarse grain heat-affected zones. J. Mater. Sci. 46 (19), 6424-6431. https://doi.org/10.1007/s10853-011-5592-7
Li, X., Fan, Y., Ma, X., Subramanian, S.V., Shang, C. (2015). Influence of martensite-austensite constituents formed at different intercritical temperatures on toughness. Mater. Des. 67, 457-463. https://doi.org/10.1016/j.matdes.2014.10.028
Lin, H.R., Cheng, G.H. (1987). Hardenability effect of boron on carbon steels. Mater. Sci. Technol. 3 (10), 855-859. . https://doi.org/10.1179/mst.1987.3.10.855
Liu, D., Guo, N., Xu, C.S., Li, H., Yang, K., Feng, J. (2017). Effects of Mo, Ti and B on microstructure and mechanical properties of underwater wet welding joints. J. Mater. Eng. Perform. 26 (5), 2350-2358. https://doi.org/10.1007/s11665-017-2629-3
Milani, J.M., Saeid, T. (2020). Acicular ferrite nucleation and growth in API5L-X65 steel submerged arc welded joints. Mater. Sci. Technol. 36 (13), 1398-1406. https://doi.org/10.1080/02670836.2020.1783774
Moeinifar, S., Kokabi, A.H., Madaah Hosseini, H.R. (2011). Role of tandem submerged arc welding thermal cycles on properties of the heat affected zone in X80 microalloyed pipe line steel. J. Mater. Process. Technol. 211 (3), 368-375. https://doi.org/10.1016/j.jmatprotec.2010.10.011
Mortimer, D.A., Nicholas, M.G. (1976). Surface and grain-boundary energies of AISI 316 stainless steel in the presence of boron. Met. Sci. 10 (9), 326-332. https://doi.org/10.1179/msc.1976.10.9.326
Mosallaee, M., Semiromi, M.T. (2021). Effect of nickel content on the microstructural, mechanical and corrosion behavior of E7018-G electrode weld metal. J. Mater. Eng. Perform. 30 (12), 8901-8912. https://doi.org/10.1007/s11665-021-06100-9
Qin, H., Guo, Y., Wang, L., Liang, P., Shi, Y., Cui, Y. (2019). Effect of heat inputs on microstructure and mechanical properties in CGHAZ of BWELDY960Q steel. Kovove Mater. 57 (5), 355-362. https://doi.org/10.4149/km_2019_5_355
Ricks, R.A., Howell, P.R., Barritte, G.S. (1982). The nature of acicular ferrite in HSLA steel weld metals. J. Mater. Sci. 17 (3), 732-740. https://doi.org/10.1007/BF00540369
Seto, K., Larson, D., Warren, P., Smith, G.D. (1999). Grain boundary segregation in boron added interstitial free steels studied by 3-dimensional atom probe. Scr. Mater. 40 (9), 1029-1034. https://doi.org/10.1016/S1359-6462(98)00485-0
Shigesato, G., Fujishiro, T., Hara, T. (2014). Grain boundary segregation behavior of boron in low-alloy steel. Metall. Mater. Trans. A 45 (4), 1876-1882. https://doi.org/10.1007/s11661-013-2155-3
Spanos, G., Hall, M.G. (1996). The formation mechanism(s), morphology, crystallography of ferrite sideplates. Metall. Mater. Trans. A 27 (6), 1519-1534. https://doi.org/10.1007/BF02649812
Terzic, A., Calcagnotto, M., Guk, S., Schulz, T., Kawalla, R. (2013). Influence of boron on transformation behavior during continuous cooling of low alloyed steels. Mater. Sci. Eng. A 584, 32-40. https://doi.org/10.1016/j.msea.2013.07.010
Uto, K., Nakayama, K., Kisaka, Y., Kimura, F., Terasaki, H. (2020). A study on the acicular ferrite formation in steel weld metals for gas metal arc welding. Quarterly Journal of the Japan Welding Society 38 (2), 6-10. https://doi.org/10.2207/qjjws.38.6s
Wang, W., Shan, Y. Yang, K. (2009). Study of high strength pipeline steels with different microstructures. Mater. Sci. Eng. A 502 (1-2), 38-44. https://doi.org/10.1016/j.msea.2008.10.042
Wang, B.X., Lian, J.B., Liu, X.H., Wang, G.D. (2014). Effect of ultra-fast cooling on microstructure and mechanical properties in a plain low carbon steel. Kovove Mater. 52 (3), 135-140. https://doi.org/10.4149/km_2014_3_135
Wang, B., Liu, X., Wang, G. (2018). Inclusion characteristics and acicular ferrite nucleation in Ti-containing weld metals of X80 pipeline steel. Metall. Mater. Trans. A. 49 (6), 2124-2138. https://doi.org/10.1007/s11661-018-4570-y
Wen, C., Deng, X., Tian, Y., Wang, Z., Misra, R.D.K. (2019). Microstructural evolution and toughness of the various HAZs in 1300-MPa-grade ultrahigh-strength structural steel. J. Mater. Eng. Perform. 28 (3), 1301-1311. https://doi.org/10.1007/s11665-019-3869-1
Winarto, W., Oktadinata, H., Siradj, E.S., Priadi, D., Baskoro, A.S., Ito, K. (2020). Microstructure and impact toughness relationship for different nickel level of electrode in multi-pass FCA welded SM570-TMC steel joint. Quarterly Journal of the Japan Welding Society 38 (2), 154-158. https://doi.org/10.2207/qjjws.38.154s
Zhang, L., Li, Y., Wang, J., Jiang, Q. (2011). Effect of acicular ferrite on cracking sensibility in the weld metal of Q690+Q550 high strength steels. ISIJ Int. 51 (7), 1132-1136. https://doi.org/10.2355/isijinternational.51.1132
Zhang, C.J., Gao, L.N., Zhu, L.G. (2018). Effect of inclusion size and type on the nucleation of acicular ferrite in high strength ship plate steel. ISIJ Int. 58 (5), 965-969. https://doi.org/10.2355/isijinternational.ISIJINT-2017-696
Published
How to Cite
Issue
Section
License
Copyright (c) 2022 Consejo Superior de Investigaciones Científicas (CSIC)
This work is licensed under a Creative Commons Attribution 4.0 International License.
© CSIC. Manuscripts published in both the printed and online versions of this Journal are the property of Consejo Superior de Investigaciones Científicas, and quoting this source is a requirement for any partial or full reproduction.All contents of this electronic edition, except where otherwise noted, are distributed under a “Creative Commons Attribution 4.0 International” (CC BY 4.0) License. You may read here the basic information and the legal text of the license. The indication of the CC BY 4.0 License must be expressly stated in this way when necessary.
Self-archiving in repositories, personal webpages or similar, of any version other than the published by the Editor, is not allowed.
Funding data
Department of Education of Liaoning Province
Grant numbers L2016132
