Determination of the hot rolling stress by means of tensile tests

Authors

  • A. Monsalve Universidad de Santiago de Chile, Dpto. Ingeniería Metalúrgica
  • A. Artigas Universidad de Santiago de Chile, Dpto. Ingeniería Metalúrgica
  • D. Celentano Departamento de Ingeniería Mecánica y Metalúrgica, Pontificia Universidad Católica de Chile
  • A. Guzmán Universidad de Santiago de Chile, Dpto. Ingeniería Metalúrgica
  • R. Colás Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León
  • Y. Houbaert Department of Materials Science and Engineering, University of Ghent

DOI:

https://doi.org/10.3989/revmetalm.1221

Keywords:

Hot rolling, Modelling, Steels, Plastic deformation, Tensile test

Abstract


Prediction of mechanical behavior of hot rolled steels is an important aspect during industrial processing. The rolling stress needed to the process were estimated using three methods, the first of which is related to the Sellars`s model that takes into account the friction coefficient and the yield stress. The second method estimates the rolling stress as the average stress obtained during the tensile tests. The third method, estimates the rolling stress from the data of power consumed by the rolling equipment. This methodology was applied in this study to a carbon steel. The conclusion of the work is that results obtained by Sellars`s and consumed power, are coincident. The method based on the average tensile stress predicts stresses lower than those obtained with other two methods.

Downloads

Download data is not yet available.

References

[1] T. Lankford, The Making Shaping and Treating of Steel, 10th Ed. USA., US Steel Co., 1985, pp. 1.069-1.070.

[2] W.L. Roberts, Hot Rolling of steels, CRC Press, USA, 1983, pp. 649-694.

[3] W.L. Roberts, Cold rolling of steels, Library Congress, New York, USA, 1978, pp. 447-489.

[4] J.G. Lenard, Primer for flat rolling, Elsevier Science Ltd., Amsterdam, 2007, pp. 36-98. http://dx.doi.org/10.1016/B978-008045319-4/50005-X

[5] G. Dieter, Mechanical Metallurgy, 3rd Ed. Mc. Graw-Hill, London, 1989, pp. 519-613.

[6] P.J. Wray, Ironmak. Steelmak. 14 (1987) 21-25.

[7] R.B. Sims, The calculation of roll forces and torque in hot rolling mills, Proceedings of the Institute of Mechanical Engineers, Vol. 168, 1954, pp. 191-198. http://dx.doi.org/10.1243/PIME_PROC_1954_168_023_02

[8] H. Ford y J.M. Alexander, Journal of the Institute of Metals 92 (1964) 397-402.

[9] J. Kokado, N. Hatta, H. Takuda, S. Kikuchi y T. Hirabayashi, Steel Research 12 (1985) 619-624.

[10] L. Béjar, C.A. Hernández y J.E. Mansilla, Rev. Latinoam. de Metalurgia y Materiales 21 (2001), 51-58.

[11] J.C. Gelin y O. Ghouati, J. Mater. Process. Tech. 34 (1994) 435-440. http://dx.doi.org/10.1016/0924-0136(94)90378-6

[12] A. Gavrius, E. Massoni y J.L. Chenot, J. Mater. Process. Tech. 60 (1996) 447-454. http://dx.doi.org/10.1016/0924-0136(96)02369-2

[13] B. Boyer y E. Massoni, Proc. of NUMIFORM 2001, Ed. K. Mori, A. Balkema, Toyohashi, 2001, pp. 281-284.

[14] R. Forestier, E. Massoni y Y. Chastel, J. Mater. Process. Tech. 125 (2002) 594-601. http://dx.doi.org/10.1016/S0924-0136(02)00406-5

[15] D. Szeliga, J. Gawad y M. Pietrzyk, Comp. Meth. Appl. Mech. Eng. 195 (2006) 6.778-6.798.

[16] D. Szeliga, J. Gawad, M. Pietrzyk y R. Kuziak, Steel Res. Int. 76 (2005) 807-814.

[17] L. Papelux y J. Philippe, J. Mater. Process. Tech. (2002) 125-131.

[18] J. Schey, Tribology in metalworking: Friction, Lubrication and Wear, ASM, Metals Park, 1983, pp. 108-112.

[19] Y. Ohkomori, C. Sakae y Y. Murakami, 42th Mechanical Working and Steel Processing Conf. Proc., 38, ISS, Warrendale, 2000, p. 723.

[20] C. Sellars, Hot working and forming process Ed. por C. Sellars y M. Davies, The Metals Soc., London, 1980.

[21] R. Colás y M. Guerrero, Laminación en caliente y en frío de aceros: Características, propiedades y microestructuras, Aceros Estructructurales: Procesamiento, Manufactura y Propiedades, M.H. Staia y J.M. Cabrera, (eds.), CYTED, Barcelona, 2003, pp. 33-64.

[22] Standard Test Methods for Elevated Temperature Tension Tests of Metallic Materials, E-21, ASTM Standards, PA, 1989, pp. 184-190.

[23] H. Avenda-o, Tesis Ing. Metal. y Magíster en Ciencias de la Ingeniería, USACH, 2005.

[24] R. Colás, J. Mater. Process. Tech. 62 (1996) 180-186. http://dx.doi.org/10.1016/0924-0136(95)02227-9

[25] J. Urcola, M. Fuentes, Rev. Metal. Madrid 16 (1980) 337.

[26] W. Callister, Introducción a la Ciencia e Ingeniería de Materiales, Ed. Reverté, Barcelona, 1998, p. 305.

Downloads

Published

2013-02-28

How to Cite

Monsalve, A., Artigas, A., Celentano, D., Guzmán, A., Colás, R., & Houbaert, Y. (2013). Determination of the hot rolling stress by means of tensile tests. Revista De Metalurgia, 49(1), 65–76. https://doi.org/10.3989/revmetalm.1221

Issue

Section

Articles