Review about laser coating of aluminium alloys
DOI:
https://doi.org/10.3989/revmetalm.2008.v44.i4.128Keywords:
Cladding, Laser, Aluminium alloy, Superficial treatmentAbstract
This article is a bibliographic review work about laser superficial treatment and cladding processes, in aluminium alloys. These laser processes are superficial modification techniques that make possible obtaining suitable properties in the surface of components, while internal properties remain unaffected. The prior advantage of laser technology is the high speed in the heating and cooling processes. This causes the formation of phases out of equilibrium, with new microstructures. Reading the article, its clear that results obtained change, not only with the alloy used as substrate or with the adding material, also with the fabrication route of the base material. Parameters, which influence the process, are analysed and the characteristics obtained by different authors are compared, with the objective of grouping the most important information of this subject.
Downloads
References
[1] R. Dekumbis, Chem. Eng. Prog. 83 (1987) 23-31.
[2] K.G. Watkins, M.A. Mcmahon y W.M. Steen, Mater. Sci. Eng. A231 (1997) 55-61. doi:10.1016/S0921-5093(97)00034-8
[3] A. Houndri, S. Polymenis, Y. Chryssoulakis y D. Pantelis, Metall. Mater. Trans. 23 A (1992) 1801-1806.
[4] A. Pantelis, E. Giannetaki, Y. Chryssoulakis y P. Ponthiaux, Plat. Surf. Finish. (1994) 52-56.
[5] Y. Liu, J. Mazumder y K. Shibata, Metall. Mater. Trans. 25 A (1994) 37-46.
[6] X. B. ZHOU y J. Th. M. DE HOSSON, Acta Mater. 42 (1994) 1.155-1.162.
[7] K. Uenishi y K.F. Kobayashi, 4th Int. Conf. Aluminum Alloys, Atlanta USA (1994) 714-720.
[8] T. Webber, Ind. Laser Review 7, 11 (1992) 5- 13.
[9] M. Brandt, D.A. Scott y J.M. Yellup, Surf. Eng. 11 (1995) 223-230.
[10] S.L. Chen y R.L. Hsu, Int. J. Adv. Manuf. Tech. (1999) 461-469.
[11] S.L. Chen y R.L. Hsu, Opt. Laser Technol. 30 (1998) 263-273. doi:10.1016/S0030-3992(98)00048-6
[12] J.A. Hopkins, M.H. Mccay, N. Dahotre, T.D. Mccay, F. Schwartz, SAE Technical paper series (1998) paper 980458.
[13] J.A. Vreeling, V. Ocelik, Y.T. Pei, D.T.L. Van Agterveld y J.TH. M. de Hosson, Acta Mater. 48 (2000) 4.225-4.233.
[14] R. Anandkumar, A. Almeida, R. Colaco, R. Vilar, V. Ocelik y J. Th. M. de Hosson, Surf. Coat. Technol. 21 (2007) 9.497-9.505.
[15] L. Dubourg, D. Ursescu, F. Hlawka y A. Cornet, Wear 258 (2005) 1.745-1.754.
[16] H.C. Man, S. Zhang y F.T. Cheng, Mater. Lett. 61 (2007) 4.058-4.061.
[17] P.H. Chong, H.C. Man y T.M. Yue, Surf. Coat. Technol. 145 (2001) 51-59. doi:10.1016/S0257-8972(01)01286-5
[18] L. Li, Opt. Laser Eng. 34 (2000) 231-253. doi:10.1016/S0143-8166(00)00066-X
[19] J. Lawrence, Proc. Institution of Mechanical Engineers, Part B: J.Eng. Manuf. 216 (2002) 1.481- 1.491.
[20] S. Iwatani, Y. Ogata, K. Uenishi, K.f. Kobayashi y A. Tsuboi, Mater. Trans. 46 (2005) 1.341- 1.347.
[21] V.M. Weerasinghe y W.M. Steen, Met. Construction 19 (1987) 581-588.
[22] J. Kelly, K. Nagarathnam, J. Mazumder, J. Laser Appl. 10 (1998) 45-54.
[23] S.D. Henry, S.E. Frueh, R. Boring, D. Levicki y L. Harrision, ASM specialty handbook, Aluminum and Aluminum Alloys, ASM International, Ed. J.R. Davis, EE. UU., 1993, pp. 23-26.
[24] K. Uenishi y K.F. Kobayashi, Intermetallics 7 (1999) 553-559. doi:10.1016/S0966-9795(98)00071-5
[25] A. Wang, C. Fan, C. Xie, W. Huang y K. Cui, J. Mater. Eng. Perform. 5(6) (1996) 775-783. doi:10.1007/BF02646913
[26] P. Sallamand y J.m. Pelletier, Mater. Sci. Eng. A 171 (1993) 263-270. doi:10.1016/0921-5093(93)90414-A
[27] Y. Liu, J. Mazumder y K. Shibata, Metall. Mater. Trans. 25B (1994) 749-759.
[28] X.B. Zhou y J. TH. M. De Hosson, Scrip. Mater. 28 (1993) 219-224. doi:10.1016/0956-716X(93)90566-B
[29] X.B. Zhou y J. TH. M. De Hosson, J. Phys. IV 3 (1993) 1.007-1.011.
[30] H.C. Man, S. Zhang, F.T. Zheng y T.M. Yue, Scr. Mater. 46 (2002) 229-234. doi:10.1016/S1359-6462(01)01230-1
[31] A.H. Wang, J.H. Nie y C.S. Xie, Mater. Lett. 56 (2002) 822-826. doi:10.1016/S0167-577X(02)00621-3
[32] K. Nagarathnam y K. Komvopoulos, Metall. Mater. Trans. 27 A (1996) 381-390.
[33] G.Y. Liang y T.T. Wong, Surf. Coat. Technol. 89 (1997) 121-126. doi:10.1016/S0257-8972(96)02932-5
[34] G.Y. Liang, C.L. Li y J.Y. Su, Mater. Sci. Eng. A224 (1997) 173-176. doi:10.1016/S0921-5093(96)10550-5
[35] W.J. Tomlinson y A.S. Bransden, Wear 185 (1995) 59-65. doi:10.1016/0043-1648(94)06584-5
[36] T.T. Wrong y G.Y. Liang, Mater. Charact. 38 (1997) 85-89. doi:10.1016/S1044-5803(97)80027-7
[37] X.B. Zhou y J.TH. M. Xe Hosson, Scr. Mater. 33, 8 (1995) 1.345-1.351.
[38] K. Uenishi, A. Sugimoto, T. Murakami y K.F. Kobayashi, Int. Conf. Laser Advanced Materials Processing 2 (1992) 807-812.
[39] W. Aihua, Z. Beidi, T. Zengyi, M. Xianyao, Shijun y C. Xudong, Surf. Coat. Technol. 57 (1993) 169-172. doi:10.1016/0257-8972(93)90035-M
[40] L.J. Li y J. Mazumder, Laser processing of materials, American Institute of Mining Metallurgical and Petroleum Engineers, New York, (1985).
[41] M.G. Pérez, A. Cortiella, H.R. Harlan, F. Zapirain y F. Zubiri, Trabajo pendiente de publicación en Revista de Metalurgia.
[42] D.K. Das, A.G. Paradkar y R.S. Mishra, Scr. Mater. 26 (1996) 1.211-1.214.
[43] M. Pierantoni, J.D. Wagniere y E. Blank, Mater. Sci. Eng. A110 (1989) L17-L21. doi:10.1016/0921-5093(89)90182-2
[44] J. Noordhuis y J. TH. M. de Hosson, Mater. Sci. Forum 163-165 (1994) 405-410.
[45] K. Uenishi y K.F. Kobayashi, Proc. 3rd Japan Int. SAMPE (1993) 1.038-1.042.
[46] J. TH. M. de Hosson, L. de Mol Van Otterloo y J. Noordhuis, Laser Processing: Surface Treatment and Film Deposition (1996) 511-527.
[47] A.B. Kloosterman y J.TH.M. de Hosson, Scr. Mater. 33 (1995) 567-573. doi:10.1016/0956-716X(95)00238-Q
[48] G.Y. Liang y J.J. Zhou, Foundry international (1994) 35-37.
[49] J. Oñoro, R. Bermejo y L. Sanchez-ibarzabal, Rev. Metal. Madrid, Vol. Extr. (2005) 40-45.
[50] A. Houndri, S. Polymenis, Y. Chryssoulakis y D. Pantelis, Metall. Mater. Trans. 23 (1992) 1.801-1.807.
[51] Y. Liu, J. Koch y J. Mazumder, Beam processing of advanced materials, Int. Conf. (1992) 141-156.
[52] A. Almeida, M. Anjos, R. Vilar, R. Li, M.G.S. Ferreira, W.M. Steen y K.G. Watkins, Surf. Coat. Technol. 70 (1995) 221-229. doi:10.1016/0257-8972(94)02263-P
[53] A.G. Crooks Y E. Hornbogen, Metall. Technik. 43 (1989) 954-960.
[54] J. Kelly, K. Nagarathnam y J. Mazumder, ICALEO (1995) 477-486.
[55] H.J. Hegge, J. Boetje y J.TH. De Hosson, J. Mater. Sci. 25 (1990) 2335-2338. doi:10.1007/BF00638023
[56] G.Y. Liang y T.T. Wong, J. Mater. Eng. Perform. 6 (1997) 41-45. doi:10.1007/s11665-997-0030-3
[57] J.A. Vreeling, V. Ocelik, G.A. Hamstra, Y.T. Pei y J. TH. de Hosson, Scr. Mater. 42 (2000) 589-595. doi:10.1016/S1359-6462(99)00404-2
[58] M.G. Pérez, N.R. Harlan, F. Zubiri, F. Zapirain y K. Gebauer, SAE Technical paper 2002-01- 2014 (2002).
[59] J.H. Ouyang, S. Nowotny, A. Richter y E. Beyer, Ceram. Int. 27 (2001) 15-24. doi:10.1016/S0272-8842(00)00036-5
[60] H.C. Man, S. Zhang, T.M. Yue y F.T. Cheng, Surf. Coat. Technol. 148 (2001) 136-142. doi:10.1016/S0257-8972(01)01339-1
[61] E. Gaffet, J.M. Pelletier, S. Bonnet-Jobez, Acta Mater. 37 (1989) 3.205-3.211.
[62] S. Bonnet-Jobez, J.M. Pelletier y A.B. Vannes, Méc. Matér. Electr. 430 (1989) 39-45.
[63] S. Mordike, Laser, Vol. 6, International Institute of Technological Transfer, Paris (1990) 99-104.
[64] G.Y. Liang y J.Y. Su, Mater. Sci. Eng. A290 (2000) 207-212. doi:10.1016/S0921-5093(00)00894-7
[65] T.T. Wong, G.Y. Liang, B.L. He y C.H. Woo, J. Mater. Proc. Technol. 100(2000) 142-146. doi:10.1016/S0924-0136(99)00463-X
[66] M.H. McCay, N. Kennedy, J.A. Hopkins, N.B. Dahotre, Lasers Eng. 10 (2000) 107-122.
[67] M. Kaneta, K. Matsuda, J. Matsuda y A. Utsumi, Wear 156 (1992) 161-173. doi:10.1016/0043-1648(92)90151-W
[68] W. Schulz y R. Poprawe, IEEE J. Sel. Top Quant. 6 (2000) 696-705. doi:10.1109/2944.883386
[69] K. Uenishi, A. Sugimoto, T. Murakami y K.F. Kobayashi, Int. Conf. Laser advanced materials processing, Vol. 2 (1992) 807-812.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2008 Consejo Superior de Investigaciones Científicas (CSIC)
This work is licensed under a Creative Commons Attribution 4.0 International License.
© CSIC. Manuscripts published in both the printed and online versions of this Journal are the property of Consejo Superior de Investigaciones Científicas, and quoting this source is a requirement for any partial or full reproduction.
All contents of this electronic edition, except where otherwise noted, are distributed under a “Creative Commons Attribution 4.0 International” (CC BY 4.0) License. You may read the basic information and the legal text of the license. The indication of the CC BY 4.0 License must be expressly stated in this way when necessary.
Self-archiving in repositories, personal webpages or similar, of any version other than the published by the Editor, is not allowed.
