New model for the prediction of the final microstructure and the dynamic recrystallization parameters of polycrystalline metallic materials. Application to AZ31 magnesium alloy
DOI:
https://doi.org/10.3989/revmetalmadrid.12XIIPMSKeywords:
Modelization, Plastic flow, Dynamic recrystallization, Magnesium alloysAbstract
The study starts from a new constitutive equation able to reproduce the stress-strain curves for each strain rate and temperature. Using this equation, the characteristic parameters of dynamic recrystallization for each of the flow curves can be obtained. An experimental study of final grain sizes, their frequency and distribution and area fractions has been made. These parameters together with those mentioned above allow establishing predictive models for the final microstructure conditions of polycrystalline metallic materials. These models have been applied to the hot deformation of AZ31 magnesium alloy. Mean final grain sizes, area fraction distributions and their frequency are predicted. In addition, the characteristic dynamic recrystallization parameters of the material that constitute elements of control of the deformation process are also predicted.
Downloads
References
[1] I. Rieiro, V. Gutiérrez, J. Castellanos,M. Carsí, M. T. Larrea y O.A. Ruano, Metal. Mater. Trans. A 41 (2010) 2.396- 2.407.
[2] I. Rieiro, M. Carsí y O.A. Ruano, Mater. Sci. Technol. 25 (2009) 995-1.002.
[3] J. Castellanos, I. Rieiro, M. El Mehtedi, M. Carsí y O.A. Ruano, Int. J. Mat. Res. 101 (2010) 787-793.
[4] V. Gutierrez, Tesis deMaestría, Universidad de Castilla La Mancha, 2009.
[5] I. Rieiro, J. Castellanos, M. Carsí, J. Muñoz, M.T. Larrea, V. Amigó y O.A. Ruano, Act. XI Cong. Nac. Tratamientos Térmicos y de Superficie, Tratermat 2008, Valencia, UPV, Valencia, España, 2008, pp.175-178.
[6] I. Rieiro, J. Castellanos, M. Carsí, D. Martín, M.T. Larrea y O. A. Ruano, Rev. Latinoam. Metal. Mater. 2 (2009) 725-734.
[7] J. Castellanos, I. Rieiro, J. Muñoz, M. Carsí y O.A. Ruano, Resúmenes XI Cong. Nac. Propiedades Mecánicas de Sólidos, El Bosque, Cádiz, España, 2008, Univ. De Cádiz, 2008, pp. 89-90.
[8] E.I Poliak y J.J. Jonas, Acta Mater. 44 (1996) 127-136. doi:10.1016/1359-6454(95)00146-7
[9] A. Galiyev, R. Kaibyshev y G. Gottstein, Acta Mater. 49 (2001) 1.199-1.207.
[10] H.J. McQueen y C.A.C. Imbert, J. Alloys Compd. 378 (2004) 35-43. doi:10.1016/j.jallcom.2003.10.067
[11] I. Rieiro, J. Castellanos, M. Carsí, J. Muñoz y O.A. Ruano,Mater. Sci. Forum 604-605 (2009) 87-96. doi:10.4028/www.scientific.net/MSF.604-605.87
[12] I. Rieiro, M. Larrea, J. Castellanos, M. Carsí, V. López y O.A. Ruano, Resúmenes XI Congreso Nacional deMateriales, Zaragoza, España, 2010, Sociemat, 2010, pp. 249-252.
[13] D. Ponge y G. Gottstein, Acta. Mater. 46 (1998) 69-80. doi:10.1016/S1359-6454(97)00233-4
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2010 Consejo Superior de Investigaciones Científicas (CSIC)
This work is licensed under a Creative Commons Attribution 4.0 International License.
© CSIC. Manuscripts published in both the printed and online versions of this Journal are the property of Consejo Superior de Investigaciones Científicas, and quoting this source is a requirement for any partial or full reproduction.
All contents of this electronic edition, except where otherwise noted, are distributed under a “Creative Commons Attribution 4.0 International” (CC BY 4.0) License. You may read the basic information and the legal text of the license. The indication of the CC BY 4.0 License must be expressly stated in this way when necessary.
Self-archiving in repositories, personal webpages or similar, of any version other than the published by the Editor, is not allowed.
