Superplastic behaviour of an AZ61 alloy processed by equal channel angular extrusion

Authors

  • M. Eddahbi Departamento de Metalurgia Física, Centro Nacional de Investigaciones Metalúrgicas, CSIC
  • O. A. Ruano Departamento de Metalurgia Física, Centro Nacional de Investigaciones Metalúrgicas, CSIC

DOI:

https://doi.org/10.3989/revmetalm.2006.v42.i2.15

Keywords:

Superplasticity, Severe plastic deformation, Magnesium alloys, Microstructure

Abstract


This study is concerned with microstructural and mechanical characterization of the superplastic behaviour of a magnesium base AZ61 alloy processed by equal channel angular extrusion (ECA). Microscopic examinations showed that the microstructure after ECA was homogeneous and the grain size was about 5 mm. The extruded material showed better mechanical properties than the rolled material. The strain rate sensitivity exponent, at 250 ºC, was 0.5 at strain rates ranging from 10-4 to 5 . 10-4 s-1. Under these conditions, the maximum elongation obtained was 250 % and the microstructure remained homogeneous and stable. Furthermore, the stress strain curves showed strong strain hardening which was not attributed exclusively to dynamic grain growth.

Downloads

Download data is not yet available.

References

[1] Superplasticity: 60 years after Pearson: Editor Norman Ridley. The Institute of Materials, London, 1995.

[2] H. Watanabe, T. Mukai, M. Mabuchi Y K. Higashi, Scripta mater. 41 (1999) 209-213.

[3] K. Kubota, M. Mabuchi Y K. Higashi, J. Mater. Sci. 34 (1999) 2255-2262. doi:10.1023/A:1004561205627

[4] T. Mukai, T.G. Nieh Y K. Higashi, Mater. Sci. Tech. 14 (1998) 32-35.

[5] M. Mabuchi, K. Ameyama, H. Iwasaki Y K. Higashi, Acta mater. 47 (1999) 2047-2057. doi:10.1016/S1359-6454(99)00094-4

[6] J.K. Solberg Y J. Tørklep, Ø. Bauger Y H. Gestland, Mater. Sci. Eng. A134 (1991) 1201-1203. doi:10.1016/0921-5093(91)90955-M

[7] W.J. Kim, S.W. Chung, C.S. Chung Y D. Kum, Acta mater. 49 (2001) 3337-3345. doi:10.1016/S1359-6454(01)00008-8

[8] H. Watanabe, T. Mukai, K. Ishikawa Y K. Higashi, Scripta mater. 46 (2002) 851-856.

[9] H. Tsutsui, H. Watanabe, T. Mukai, M. Kohzu, S. Tanabe y K. Higashi, Mater. Trans. JIM 40 (1999) 931-934.

[10] Y.N. Wang Y J.C. Huang, Scripta mater. 48 (2003) 1117-1122.

[11] V.M. Segal, Mater. Sci. Eng. A271 (1999) 322- 333. doi:10.1016/S0921-5093(99)00248-8

[12] Z. Horita, K. Matsubara, K. Makii Y T.G. LANGDON, Scripta mater. 47 (2002) 255-260.

[13] T. Mukai, H. Watanabe Y K. Higashi, Mater. Sci. Forum (2000) 15-170.

[14] Y. Iwahashi, M. Furukawa, Z. Horita, M. Nemoto Y T.G. Langdon, Metall. Mater. Trans. 29A (1998) 2245-2252.

[15] M. Eddahbi, Informe Anual, Conserjería de Educación de la Comunidad Autónoma de Madrid (CAM), 2003.

[16] P.A. González, C.L. Pérez, Y. Garcés Y J. Gilsevillano, Rev. Metal. Madrid 37 (2001) 673- 692.

[17] W.J. Kim, C.W. An, Y.S. Kim, S.H. Min Y S.I. Hong, Scripta mater. 47 (2002) 39-44.

[18] M. Eddahbi, J.A. Del Valle, M.T. Pérez-Prado Y O.A. Ruano, Mater. Sci. Eng. (2005) 308-311.

[19] Y. Yoshida, L. Cisar, S. Kamado Y Y. Kojima, Mater. Trans. 4 (2003) 468-475. doi:10.2320/matertrans.44.468

[20] W.J. Kim, S.I. Hong, Y.S. Kim, S.H. Min, H.T. Jeong Y J.D. Lee, Acta mater. 51 (2003) 3293- 3307. doi:10.1016/S1359-6454(03)00161-7

[21] J. Koike, T. Kobayashi, T. Mukai, H. Watanabe, M. Suzuki, K. Maruyama Y K. Higashi, Acta mater. 51 (2003) 2055-2065. doi:10.1016/S1359-6454(03)00005-3

[22] T. Mukai, M. Yamanoi, H. Watanabe Y K. Higashi, Scripta mater. 45 (2001) 89-94.

[23] H.T. Jeong, K.K. Um Y D.N. Lee: Analysis of Inhomogeneous Rolling Texture of FCC Metal Sheets: Editor J.A. Szpunar, Pro. De ICOTOM12, 1. Ottawa: NRC Research Press, 1999, p.26-7.

[24] N. Ridley, Mater. Sci. Technol. 6 (1990) 1145- 1156.

[25] H. Gudmundsson, D. Brooks Y J.A. Pert, Acta metall. mater. 39 (1991) 19-35.

[26] Y.N. Kwon, H.J. Koh, S. Lee, N.J. Kim Y Y.W. Chang, Metall. Mater. Trans. 32A (2001) 1649- 1658.

[27] T. Sakai, X. Yuyue Y H. Miura, Mater. Sci. Eng. A234 (1997) 857-860. doi:10.1016/S0921-5093(97)00398-5

[28] M. Eddahbi, T. Mcnelley Y O.A. Ruano, Metall. Mater. Trans. 32A (2001) 1093-1102.

[29] H. Watanabe, T. Mukai, M. Kohzu, S. Tanabe Y K. Higashi, Acta mater. 47 (1999) 3753- 3758. doi:10.1016/S1359-6454(99)00253-0

Downloads

Published

2006-04-30

How to Cite

Eddahbi, M., & Ruano, O. A. (2006). Superplastic behaviour of an AZ61 alloy processed by equal channel angular extrusion. Revista De Metalurgia, 42(2), 146–157. https://doi.org/10.3989/revmetalm.2006.v42.i2.15

Issue

Vol. 42 No. 2 (2006)

Section

Articles

License

Copyright (c) 2006 Consejo Superior de Investigaciones Científicas (CSIC)

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

© CSIC. Manuscripts published in both the printed and online versions of this Journal are the property of Consejo Superior de Investigaciones Científicas, and quoting this source is a requirement for any partial or full reproduction.

All contents of this electronic edition, except where otherwise noted, are distributed under a “Creative Commons Attribution 4.0 International” (CC BY 4.0) License. You may read here the basic information and the legal text of the license. The indication of the CC BY 4.0 License must be expressly stated in this way when necessary.

Self-archiving in repositories, personal webpages or similar, of any version other than the published by the Editor, is not allowed.
Crossref
Scopus
Google Scholar
Europe PMC

Most read articles by the same author(s)

1 2 3 > >>