Influence of different inoculants on the nucleation potential and the contraction ability of the ductile iron
DOI:
https://doi.org/10.3989/revmetalm.0840Keywords:
Nucleation potential, Contraction susceptibility, Spheroidal grafite iron, Inoculation, Solidification, Thermal analysisAbstract
The use of advanced control systems based on cooling curves allows to analyse the characteristics of the melt in real time along the manufacturing process. In this work, the system mentioned above has been utilised so as to study the efficiency of the inoculation step, to determine which substrates have the optimum ability for nucleating spheroidal graphite, to minimise the tendency to form cementite phase and to reduce the capacity of the melt to form microshrinkage defects. Thus, 10 different commercial inoculants have been selected in order to investigate the efficacy of several chemical elements included in their composition for nucleating nodules in ductile iron. In addition, trials performed on real castings are included in this work so as to verify the results obtained from the selected inoculants.
Downloads
References
[1] I.G. Chen y D.M. Stefanescu, AFS Trans. 92 (1984) 947-964.
[2] Y.X. Li, X.R. Xu, Q. Wang y B.C. Liu, Int. J. Cast Met. Res. 16 (2003) 41-45.
[3] P. Larrañaga, J. M. Gutiérrez, A. Loizaga, J. Sertucha y R. Suárez, AFS Trans. 112 (2008) 547- 561.
[4] J. Tinoco, P. Delvasto, O. Quintero y H. Fre driksson, Int. J. Cast Met. Res. 16 (2003) 53-58.
[5] C. Labrecque y M. Gagné, AFS Trans. 106 (1998) 83-90.
[6] J. Sertucha, R. Suárez, J. Izaga, L.A. Hurtado y J. Legazpi, Int. J. Cast Met. Res. 19 (2006) 315- 322. doi:10.1179/136404606X167114
[7] T. Skaland y Ø. Grong, AFS Trans. 99 (1991) 153-157.
[8] J. Lacaze, Acta Mater. 47 (1999) 3.779-3.792.
[9] L. Battezzati, M. Baricco, C.A. Coria, G. Serramoglia y F. Marongiu, Int. J. Cast Met. Res. 16 (2003) 87-92.
[10] S. Jung, T. Ishikawa y H. Nakae, Mater. Sci. Eng. A 476 (2008) 350-356. doi:10.1016/j.msea.2007.07.013
[11] C.R. Loper y K. Fang, AFS Trans. 112 (2008) 673-682.
[12] P. Larrañaga, J. Sertucha y R. Suárez, Rev. Metal. Madrid 42 (2006) 244-255. doi:10.3989/revmetalm.2006.v42.i4.24
[13] M.I. Onsøien, Ø. Grong, T. Skaland y S.O. Olsen, AFS Trans. 105 (1997) 147-152.
[14] A. Louvo, E. Alhainen Pellikka y P. Eklund, AFS Trans. 99 (1991) 237-244.
[15] C.A.S. Ribeiro, D. Santos, W. Baumgart, F. Vilela y C. Henke, Int. J. Cast Met. Res. 20 (2003) 47- 52.
[16] I. Asenjo, P. Larrañaga, J. Sertucha, R. Suárez, J.M. Gómez, I. Ferrer y J. Lacaze, Int. J. Cast Met. Res. 20 (2007) 319-324. doi:10.1179/136404608X286138
[17] S. Lekakh y C.R. Loper, AFS Trans. 111 (2003) paper 03-103.
[18] S.O. Olsen, T. Skaland y C. Hartung, Proc. 66th World Foundry Congress, Estambul, Turquía, 2004, pp. 891-902.
[19] T. Skaland, Tesis Doctoral, Metallurgisk Institutt, Trondheim, Norway, 1992.
[20] A. Loizaga, J. Sertucha y R. Suárez, Rev. Metal. Madrid 44 (2008) 432-446.
[21] J. F. Wallace y R.D. Maier, Proc. AFS-CMI Conf., Rosemont, Illinois, EE. UU., 1979, pp. 41-73.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2009 Consejo Superior de Investigaciones Científicas (CSIC)

This work is licensed under a Creative Commons Attribution 4.0 International License.
© CSIC. Manuscripts published in both the printed and online versions of this Journal are the property of Consejo Superior de Investigaciones Científicas, and quoting this source is a requirement for any partial or full reproduction.
All contents of this electronic edition, except where otherwise noted, are distributed under a “Creative Commons Attribution 4.0 International” (CC BY 4.0) License. You may read the basic information and the legal text of the license. The indication of the CC BY 4.0 License must be expressly stated in this way when necessary.
Self-archiving in repositories, personal webpages or similar, of any version other than the published by the Editor, is not allowed.