Mechanical and microstructural evolution of a 3xxx aluminium alloy made by hazelett process
DOI:
https://doi.org/10.3989/revmetalm.2007.v43.i6.85Keywords:
Hazelett process, AA3005, Recrystallization, Precipitation, Mechanical properties, Microstructural characterizationAbstract
This paper presents the thermal, microstructural and mechanical changes of a AA3005 aluminium alloy during the different stages of manufacturing process, from continuous cast billet (20 mm thick) , along the different plastic deformation stages, till the last lamination (1.5 mm thick). The optical and scanning electron microscopy study of the different sheets obtained both in the cast and after each lamination, as well as the differential scanning calorimetry study has allowed us to identify the different thermal states of the sheets. The information provided by this technique was completed by transmision electron microscopy analysis. The interaction between the different processes occurred in the material during its manufacturing determines its final microstructural state, its mechanical properties, evaluated with hardness and tensile tests, as well as its behaviour for later forming processes. The recrystallization and precipitation phenomena increase mechanical properties during the manufacturing process.
Downloads
References
[1] W. Hufnagel y P. Coca, Manual del Aluminio. Ed. Reverté, Barcelona, España, 1992, pp. 26-255.
[2] L.F. Mondolfo, Aluminium alloys. Structure and properties, Ed. Butterworths, 1976, pp. 173.
[3] J.A. González, E. Escudero, V. López, J. Simancas y M. Morcillo, Rev. Metal. Madrid 40 (2004) 259-269.
[4] S. Ding, Phys. Metall. Mater. Sci.28 (1997) 2.715.
[5] A. Bahadur, J. Mater. Sci. 23 (1998) 48-54. doi:10.1007/BF01174033
[6] J. Pérez-Ilzarbe, J. Faustmann-Salas y A. Suárez-Sanabria, Rev. Metal. Madrid 36 (2000) 435-451.
[7] www.Hazelett.com
[8] P. Furrer y H. Warlimont, Res. Dev. 54 (1978) 135-142.
[9] E. Nes y S. Slevolden, Comunication fron Central institute for Industrial Research, Blinderm 55 (1979) 319-323.
[10] R.G. Kamat y S. Saimoto, Mater. Sci.Techonol. 10 (1994) 215-221.
[11] H. Bjerkaas, S.K. Fjeldbo, J. Hjelen, B. Holmedel, O.G. Lademo y S. Storen, Proc. ESAFORM, 1 (2005) 209-212.
[12] P. Barrand y R. Gadeau, Enciclopedia del Aluminio, Vol 2, 1981, pp. 68-249.
[13] V. Amigó y A.V. Escuder, Materials per a disseny industrial. Aliatges Metàl.lics, Ed. UPV, 2003, pp. 141-173.
[14] O.M. Suárez, Rev. Metal. Madrid 40 (2004) 173-181.
[15] C.A. Bloem, M.D. Salvador, V. Amigó y D. Busquets, Rev. Metal. Madrid 39 (2003) 298-303.
[16] J. Li, S. Saimoto, Mater. Sci. Eng. A 234-236 (1997) 1.011-1.014.
[17] D.L. Sun, S.B. Kang y H.S. Koo, Mater. Chem. Phys. 63 (2000) 37-43. doi:10.1016/S0254-0584(99)00198-4
[18] D.T.L. Alexander y A.L. Greer, Acta Mater. 50 (2002) 2.571-2.583.
[19] J.M. Howe, Metall. Mater. Trans. A, 17 (1986) 593-605. doi:10.1007/BF02643978
[20] C.H. Gras, M. Meredith y J.D. Hunt, J. Mater. Process. Technol. 169 (2005) 156-163. doi:10.1016/j.jmatprotec.2005.03.034
[21] J. Ney y A. Luiggi, Cienc. 12 (2006) 1-21.
[22] S.P. Chen, N.C.W. Kuijpers y S. Van Der Zwaag, Mater. Sci. Eng. A 341 (2003) 296-306. doi:10.1016/S0921-5093(02)00245-9
[23] O. Daaland y E. Nes, Acta Mater. 44 (1996) 1.413-1.435.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2007 Consejo Superior de Investigaciones Científicas (CSIC)

This work is licensed under a Creative Commons Attribution 4.0 International License.
© CSIC. Manuscripts published in both the printed and online versions of this Journal are the property of Consejo Superior de Investigaciones Científicas, and quoting this source is a requirement for any partial or full reproduction.
All contents of this electronic edition, except where otherwise noted, are distributed under a “Creative Commons Attribution 4.0 International” (CC BY 4.0) License. You may read the basic information and the legal text of the license. The indication of the CC BY 4.0 License must be expressly stated in this way when necessary.
Self-archiving in repositories, personal webpages or similar, of any version other than the published by the Editor, is not allowed.